Search results

I actually have another Klepper Kamerad TS that I picked up a couple years ago. I haven't rigged a permanent seat or rudder on it yet, but it paddles well with a single blade sitting on a small plastic kids shower stool. This hull is a Kamerad W. I haven't done a full comparison, but this...

Their bloody multiplying...

That is clever.

The one break in the gunnel shown is the only fatal injury. I'm sure I could coble a patch in a survival situation... I still need to get an accurate measurement of the gunnels but hopefully their under the 18.5 ft stock I found on line. My initial goal is to do the structural glass work...

This boat cost me $1 to get in to. Aluminum gunnels will be another $200. Add another $100 for glass, goop and paint. This hull may be a candidate as an ACA sailing canoe, so I'll be holding off on gunnels for the time being. The gelcoat is pretty rough so, this hull will get painted, so...

I acquired a damaged Wenonah Toughweave Sundowner that was on its way to the dump. Apparently it had a misadventure and wrapped around something or was crushed. The rails are kinked in a number of places and will need to be replaced. I'm going to straighten them out to get the hull fair...

Epoxy is sensitive to uv degradation. Polyester is also, which is most obvious with chalky gelcoat. I've got a bunch of semi neglected unfinished epoxy projects that have been sunburned. I've consulted the West Systems techs, and have been told that its best to grind it all off for a 100%...

Cold Steel has created "The horror that can not be unseen"....

Definitely going to set up for sailing. Im not sure how far into the wind. I have a 1 meter BSD sail that should work for motor sailing. Seating is a big part of the puzzle. I've never really taken to kayak paddles, so higher seat is required. Simple solution is a Wenonah sliding pedestal...

Why yes it is. Hens teeth may only appeal to the discerning palate......

I spent a lot of time with a 15' fiberglass Great Canadian. Its a heavy boat with a shallow v bottom. I paddled it successfully seated on the rear seat, with a rock or a couple milk jugs holding the bow down. I generally healed the boat as much as comfortable and was able to get the paddle...

I happened to find a broken fiberglass arborist pole today. The Aluminum ferrule looks like it would be awkward to use. But the fiberglass pole it self looks like it might make a good joint with an an internal sleeve/pin. That's a bit of a DIY though.

Have you poked around the UK based "Song Of The Paddle" forum? As I remember there was a developed technology of 2 part poles that could be used to with a small down wind sail. Its probably not worth shipping poles from the UK, but there's always some one trying to find a low cost...

I looked on Ebay and there are a couple vintage single burners with hoses that where available at some point. There are also single burner catering stoves direct from China, but those are a gamble. If I can attach the stove and bottle to a board, I should be able to also secure a wind...

https://www.forestry-suppliers.com/p/81051/17161/Wood%20Spruce%20Extension%20Pole,%201-1/4%E2%80%9D%20Dia.%20x%206%E2%80%99L This might be as close as your going to find.

I believe the Texsport sits flat and has a rigid tube that holds the fuel bottle at an angle, just like most of the the 2 burner stoves. Texsport makes a even cheaper and lighter version, but the review mention the stove body not having enough mass to stabilize the fuel bottle, leading to...

I think I narrowed down the stove I will use for this. It's a "Texsport Glacier Peak Deluxe Single Burner Propane Stove" I haven't picked one up yet, but the hope is that I can attach it to a board that will also support the fuel bottle, and some how nest into the wannigan that nests in a...